Lift-Top and Lift-Bottom Furnaces with Molybdenum Disilicide Heating Elements up to 1800 °C
 PRODUCT IMAGE PRODUCT IMAGE
 HT 276/17 LT with manual table changing system HT 276/18 LTS with two inner process hoods for sintering under non-flammable protective or reaction gases
PRODUCT IMAGE

HT 64/17 LT

PRODUCT IMAGE

HT 680/17 LTS2 with table exchange system

PRODUCT IMAGE

Heat from all sides and between the stack to optimize temperature uniformity

HT 64/14 LB or LT - HT 1440/17 LB or LT

For charging complex settings we recommend lift-top or lift-bottom furnaces. Also small workparts can be conveniently loaded on different layers. Up to an application temperature of 1500 °C the furnaces are heated by SiC rods (HTC models). For sintering temperatures above 1500 °C these furnaces with molybdenum disilicide heating elements (HT models). Possible potential chemical interaction between the charge and the heating method can also affect the selection of heating system.

The basic furnace comes with one table. Depending on the technical requirements are equipped, a lift-top or lift-bottom version will be the choice. The system can be expanded with one or more changeable tables, either manually or electrically driven. Other additional equipment, like controlled cooling systems to short process cycles provide for tailored solution for individual needs.

  • Tmax 1400  °C or 1500  °C (HTC models with SiC rod heating)
  • Tmax 1600  °C, 1750  °C or 1800  °C (HT models with molybdenum disilicide heating elements)
  • Dual shell housing with fan cooling provides for low shell temperatures
  • Designed as lift-top furnace with driven hood (LT) or lift-bottom furnace
  • Gently running, low-vibration spindle drive or electrohydraulic drive for larger models
  • Safe and tight closing of the furnace due to labyrinth seal and sand cup
  • Heating from all four sides provides for good temperature uniformity
  • High-quality fiber insulation backed by special insulation
  • Side insulation constructed with tongue and groove blocks provides for low heat dissipation to the outside
  • Long-life roof insulation with special suspension
  • Furnace table with special bottom reinforcement to accommodate high charge weights
  • Motor-driven exhaust air flap in the furnace roof, switchable at the program
  • PLC controls with state-of-the-art touch panel as user interface
  • Over-temperature limiter with manual reset for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load

Additional equipment

  • Customized dimensions
  • Uncontrolled or controlled cooling system with frequency-controlled cooling fan and motor-driven exhaust air flap
  • Commissioning of the furnace with test firing and temperature uniformity measurement (also with load) for the purpose of process optimization
  • Temperature measurement with thermocouples, types B and type S with automatic pull-out device for precise control results in the low temperature range
  • Heat from all sides and between the stack to optimize temperature uniformity
  • Protective gas connection to purge with non-flammable protective or reaction gases
  • Manual or automatic gas supply systems
  • Gas supply system in the furnace chamber with ceramic bell jar, protective gas inlet and outlet from below for better sealing when operating with protective gases and/or to prevent from chemical interactions between the load and the insulation or the heating elements
  • Alternative table changing systems
  • Emergency purging with protective gas
  • Exhaust air and exhaust gas piping
  • Automatic changing system for thermocouple type S/B for precise measurement and control quality at lowes temperatures
  • Thermal or catalytic exhaust cleaning systems
  • Process documentation, display and control via HiproSystems control system
ModelTmaxInner dimensions in mmVolumeOuter dimensions in mmConnectedElectricalWeight
 °Cwdhin lWDHload kWconnection*in kg
HT 64/16 LB, LT16004004004006495017502350363-phase1000
HT 166/16 LB, LT1600550550550166109520602450423-phase1600
HT 276/16 LB, LT16001000500550276155020902600503-phase2000
HT 400/16 LB, LT16001200600550400175022002600723-phase2200
HT 1000/16 LB, LT160010001000100010001550260032001463-phase3000
HT 1030/16 LB, LT1600220060078010302800250030001633-phase3000
HT 1440/16 LB, LT16001800800100014403000280037003303-phase4000
            
HT 64/17 LB, LT17504004004006495017502350363-phase1000
HT 166/17 LB, LT1750550550550166109520602450423-phase1600
HT 276/17 LB, LT17501000500550276155020902600503-phase2000
HT 400/17 LB, LT17501200600550400175022002600723-phase2200
HT 1000/17 LB, LT175010001000100010001550260032001463-phase3000
HT 1030/17 LB, LT1750220060078010302800250030001633-phase3000
HT 1440/17 LB, LT17501800800100014403000280037003303-phase4000
            
HT 64/18 LB, LT18004004004006495017502350on request3-phase1000
HT 166/18 LB, LT1800550550550166109520602450on request3-phase1600
HT 276/18 LB, LT18001000500550276155020902600on request3-phase2000
HT 400/18 LB, LT18001200600550400175022002600on request3-phase2200
HT 1000/18 LB, LT18001000100010001000155026003200on request3-phase3000
HT 1030/18 LB, LT180022006007801030280025003000on request3-phase3000
HT 1440/18 LB, LT1800180080010001440300028003700on request3-phase4000
*Please see page 61 for more information about supply voltage

glas_englisch catalogue Glass
(URL: http://www.nabertherm.com/produkte/glas/glas_englisch.pdf)